Slightly restricted planer suggestions

[myimpishgrin]

Good evening all,

I come in search of wisdom, or in lieu of that some experience. I'm hunting for a planer thicknesser for my little hobbiest wood shop that I'm currently building. I'll give some further detail here, but I'll drop tldr bulletpoints at the bottom. Space is fairly limited in there so with that in mind I'm aiming for something with a depth of no more than 800mm (preferably 750mm). I'd also be keen for helical head or spiral head rather than standard knives (I have a little lunch box metabo that screams like a banshee and I'd rather something a little less vocal), but I'd be willing to look at tersa too, though I haven't seen any in my size and price range. Speaking of price, I was hoping for something around the £2000 mark, though I'd be willing to go higher if the machine was deemed enough of an upgrade on the others and it was a sort of "buy once, cry once" situation. Power wise the workshop is in a garage with its own distribution board, but it's just standard home level supply to the best of my knowledge (I didn't build the garage so I'm just going on how it looks). I am considering getting a spark in to quote for upgrading the power given there will be some other machinery and a separate room with a fridge and freezer in it on the circuit, so I won't 100% rule out something that needs more than a standard 3 pin plug.

One slight complication is the fact that I'm in Northern Ireland. That greatly limits my access to the larger UK 2nd hand market unfortunately so barring a stroke of good luck and old sedgwick or something popping up locally, buying and older machine probably isn't an option. It makes shipping expensive (or people just refuse) but I'll just have to swallow that.

I've been looking at the 4 below that fall into these categories

Record Power PT310-HB £2499
Record Power PT107-HB £1899
iTECH 260SS £2028
Jet JPT-310HH £3792

I realise the jet is quite a jump in price, but if it's much better regarded than the other options then I might be able to justify the cost to myself.

So if anyone has any experience of any of these machines I'd love to hear about them, good and bad. Alternatively if anyone has any other suggestions available in the UK / Ireland that match those specs, I'm all ears.

TLDR:
Planer thicknesser
800mm (preferably 750mm) footprint depth
Helical / spiral / tersa cutters
Around £2000 (flexible for the right bit of kit)
Currently standard 240v supply (potentialy to change)
Based in NI so 2nd hand less feasible

Thank for any help you can provide

Pete

 

[Sideways]

Hi Pete.
Welcome to UKW.
You will notice that I've removed four web links from your 1st post above.
Forum software like ours and others automatically assumes that any new sign up to a forum who includes web links in their first few posts is a spammer and just trying to sneak advertising into forums by catching people's interest.
Hopefully that isn't you and I've approved the publishing of your thread, but the web links aren't actually necessary to your question so I've deleted them.
This is an opportunity to point out this common type of spam to you and the other members so I'm making use of your thread. There's no criticism intended.

I'm sure members will soon be along with good advice

PS. Please pop along to the "new members" area and introduce yourself to everyone.
Cheers.

 

[myimpishgrin]

Hi Sideways,

Thanks for the heads up on the link issue, and no offence taken

 

[Ilya]

Hi,
just got the Axi AP310SPT, which may also be a variant to consider for you. Was also very much concerned with the footprint, as I am in a one car garage. But surprisingly the machine is really compact when not in use. Easily fits in the 700-800mm depth.

PS. they've got a smaller model, which should be even smaller a bit, but from what I realised - depth footprint is nearly the same for both 12" and 10" inch models (similar to iTECH and others), so my point is that although these machines may appear huge on pictures, they are surprisingly compact in reality of a UK-style one-car (i.e. frustratingly small) garage-size workshop.

 

[myimpishgrin]

Hi,
just got the Axi AP310SPT, which may also be a variant to consider for you. Was also very much concerned with the footprint, as I am in a one car garage. But surprisingly the machine is really compact when not in use. Easily fits in the 700-800mm depth.

PS. they've got a smaller model, which should be even smaller a bit, but from what I realised - depth footprint is nearly the same for both 12" and 10" inch models (similar to iTECH and others), so my point is that although these machines may appear huge on pictures, they are surprisingly compact in reality of a UK-style one-car (i.e. frustratingly small) garage-size workshop.

Interesting. I'd discounted all the axminster ones because the depth on the dimensional drawings were all over 900mm. Will have to have another look.

 

[Ilya]

Interesting. I'd discounted all the axminster ones because the depth on the dimensional drawings were all over 900mm. Will have to have another look.

Yes, that was my point also, but their footprint photos, though very good and I really appreciate they do it, they sometimes are a bit misleading. In this particular case they show with the fence fully extended. But when not in use, you can pull the fence forward and that gives you the minimal footprint. I will post a photo later on today.

On a side note, what I did found, which was a bit of a nasty surprise for me (and may be someone can advise me on that) - the in-feed roller on that planer, and I suspect on all other planer-thicknesser as well - is corrugated.

This means that if I make light passes in thickness mode, it does leave marks on the timber.
Whereas my previous lunchbox thicknesser had both infeed and outfeed rollers smooth, which gave me an option to make very light passes just to clean up and the finish was perfect.

What I was expecting by the upgrade is that this would be upgrade form that, not a downgrade. So now I am sort of a fit frustrated with the outcome. Although the machine itself works perfectly fine. I think it is a common design feature of such type of combined machines.

 

[myimpishgrin]

Yes, that was my point also, but their footprint photos, though very good and I really appreciate they do it, they sometimes are a bit misleading. In this particular case they show with the fence fully extended. But when not in use, you can pull the fence forward and that gives you the minimal footprint. I will post a photo later on today.

On a side note, what I did found, which was a bit of a nasty surprise for me (and may be someone can advise me on that) - the in-feed roller on that planer, and I suspect on all other planer-thicknesser as well - is corrugated.

This means that if I make light passes in thickness mode, it does leave marks on the timber.
Whereas my previous lunchbox thicknesser had both infeed and outfeed rollers smooth, which gave me an option to make very light passes just to clean up and the finish was perfect.

What I was expecting by the upgrade is that this would be upgrade form that, not a downgrade. So now I am sort of a fit frustrated with the outcome. Although the machine itself works perfectly fine. I think it is a common design feature of such type of combined machines.

That's great Ilya, a picture and a measurement of it with the fence pulled forward to the maximum extent would be very much appreciated.

That's interesting about the corrugated in-feed, I'd never thought of that

 

[Ilya]

Here are some photos. It is on a wheel kit (vevor wheel kitfits it perfectly, not the Axminster one - they apparently do not have a proper wheel kit for it and what they have only has 2 castors, but I found for the same price a one from Vevor tools with 4 castors) - so the castors themselves take a fair bit of space behind, but even with them it is still quite reasonable.

And there is a picture of what it makes if I try to do a very light pass. I do not think that is a machine fault, I think I am doing something wrongly, as I am quite new to it.

 

[Spectric]

I'm hunting for a planer thicknesser for my little hobbiest wood shop that I'm currently building.

Have you asked yourself if you really need one ? If you have a good source of wood then maybe the space could be used by something else and the money saved would buy it. Also some of these machines require a 16 amp supply so something else to bear in mind.

 

[Ilya]

Have you asked yourself if you really need one ? If you have a good source of wood then maybe the space could be used by something else and the money saved would buy it. Also some of these machines require a 16 amp supply so something else to bear in mind.

Yes, btw - mine is on 16amp

 

[myimpishgrin]

Have you asked yourself if you really need one ? If you have a good source of wood then maybe the space could be used by something else and the money saved would buy it. Also some of these machines require a 16 amp supply so something else to bear in mind.

I know what you mean, it's probably not a necessity, but it would be very convenient and as far as machinery goes, it would probably be that and a bandsaw and I'd be done. I'd like to be able to resaw my own material and those 2 tools would make that a whole lot simpler. Power wise I am planning to get a spark out to look at getting things beefed up anyway so I have factored that in, but if the cost is prohibitive then obviously that will limit my choices too.