Search results

Are you sure you have room for a proper table saw especially with sliding table its very difficult to get dimension from adds. they seem to leave the sliding table size off.

This may be a good place to start. http://www.itsnoteasybeinggreen.org/forum/

concrete is strong in compression to break it you force a chisel in to fracture the structure , so expanding fixings may not be a good idea you could resin glue threaded rod into the floor to give a good fixing without side force. Clean holes out well for a good fixing and spread the load.

I have a SIP 1hp ( same as axmin.)mounted in a separate enclosure and it works fine with a p/t etc but is two bag type so better flow. I removed the nvr and covered the hole. its two wires in, two out just connect them through mine is plugged in to socket via remote switch unit so i can...

I would think if the height difference is small you could loose it in the distance to under the windows by adjusting the overlaps using story boards and string line, it will not be seen . larger distances could be fixed by a solid timber starter board suitably tapered and profiled to accept the...

I like the angle iron idea with perhaps some saw cuts in the style so its pulled straight by the steel.

Before anyone will consider cutting reclaimed timber they need to be sure there is no steel or stone in it as it will ruin the blade.So wire brush down for grit etc and metal detect any one with suitable machines would then be able to help.

Is everything clean no resin sawdust etc clogging any of the threads, housings or expansion slots is the bit in to far so the radius where it flares out is expanding the adapter sleave. are the threads worn allowing them to ride over each other all worth a clean up and check .

I got a dvd with mine which answers most questions sorry but i am not able to copy at the moment. when fixing in clamp just angle the job to give a square cut set the angle gauge to the higher angle of the range as it will be hollow ground, flatten the back using your preferred method, oil the...

I believe its a good idea to keep the sheets wet as it helps to hold any free fibres. Where we are you just take it to the reclaim centre and it goes in a specific skip.

There is usually a stopcock external to property to isolate your supply so that the valve can be serviced/replaced they some times get stiff. Bit of work with the gass pliers gets them to shut off.

In my axminster cat. there is only the LS1040 260 mm mitre saw this has a good reputation £156 . The LS1040 should do the job, the discrepancy you mention is less than one percent (2mm in 305mm) picture framing kit may be what he requires, they do a mitre trimmer for £100.Cut with saw and trim...

Just confirming the above my workshop flat roof uses ply to the top then three layer felt . you can just hear thunder storm rain but any other is quiet

PM sent. New spare try. http://www.mtmc.co.uk/default.asp?cookiecheck=yes&

I employed a aerial fitter he said that the existing aerial was good on the high frequencys used so a new large digital one would give a small improvement only. So we went for a 4 way masthead adjustable amp with separate power supply which all use F type connectors that fixed the problem which...

Info on span is herehttp://www.stapeley1.plus.com/build%20regs%20&%20calcs.pdf page 44 has span of 53x97 at 400 spacing as 1.67 mts for loads of 0.5 to 1.25 kn/m.squared is this any help.

Current set up analog ariel then a one way 12db amp in loft to humax digital box in bedroom all is fine but i want to feed two more rooms from loft and if i try a old 3 way distributing amp with lower gain using good coax to all, the bedroom set gets picture and sound drop outs on chans.3&4 so...

This is how it arrived the ebay seller sent back all the money so i straightened the fan under the bobbing sleave and made a box to rehouse the mechanics it works fine so difficult to beat for the price i seem to be getting quite lucky in my old age

When you connect the two 6' x 10' brick outhouses what size will you have 12x10 or 6x20 etc.

You must have the wrong type of blade fitted the kerf should be greater than the knife thickness or the knife is trying to force the wood apart this happens when narrow kerf blades are fitted.Axminster cat. has kerf width info.