Search results

I think you are correct it will trip the breaker start up current under load is very high for a instant until the motor starts to move . If the feed cable is thick enough then its a breaker uprating job if not then a new feed cable say 2.5mm ( gives 27 extra amps ) in parallel with the existing...

I have a similar saw and if i cannot tension the blade as you indicate i put a washer cut in a 'U' in the tension wheel and rod mec. to compensate and readjust.

I think the cable needs to carry only 1.6 amps so 2.5sq.mm would be over rated and may be difficult to terminate on the tool. calculations are 1 hp is 746 watts ,watts equals volts x amps plus small round up for type of device powered.

This is a difficult area, my lplv spray gun needs 22psi and 6.2 cfm so a 2.5 hp 9.5 cfm 24ltr from amazon £80 sould have done the job. But no the compressor is running all the time and the pressure at the gun drops quickly i think the 9.5 cfm is piston displacement not output. The answer was to...

Our posh kitchens in Nantwich Cheshire can be found in the link with lots of google images that may give you some ideas but it looks like the legs go at the ends of large unit runs. https://www.google.co.uk/webhp?sourceid ... 20kitchens

Shed security .YouTube video ultimate handyman shed security .he uses unistrut thought you might be interested. https://www.youtube.com/watch?v=wnx64xT ... PcaG_K5WHw

I think graduate_owner is correct its a neutral/earth fault .Also check that motor and switch gear is not full of dust.One other possibility is that heat is causing the motor insulation to break down after running for a short time

Just put insulated plaster board in google and find what fits your room arrangement and space requirement, check out installation instructions . When complete consider supplementary heating . Just noticed your profile , you could find the above job heavy and difficult for one person .

I think you should stick with the bosch its more versatile and not that much bigger ,also that base unit will be useful for long material and its mobile.

I think when you register it a lot of info about your computer build is sent so altering where its installed looks like a additional computer try contacting adobe

Nice tidy installation you have there i would replace the 40a to sockets with a 20a that should be fine for you requirements then fit the 16a wired from the buss bars in a separate box or expand the existing thus maintaining the protection of the rcd.

What no one has mentioned is the 16a plug and socket does not have a fuse, unlike 13a plugs so it needs to be wired directly to a 16a circuit breaker class c fitted to a distribution unit .That in your case can supply up to 40a, so this is a stand alone supply to a 16a socket that will only...

Just split the false jaws remove screws and make new wood jaws .

I would imagine that after your health problem that you will be avoiding the heavy work if you can, how ever i think i am right in thinking that the breather membrane is only good for 3 months in mild weather so the roof could be a problem .Please check this before you alter your plans or buy in...

Your question is about door hardware, so does this mean that you are thinking about whole building security. As we all know any security can be breached but we can make it difficult, time consuming and increase the risk of getting caught doing it. Would it be idea to talk with a crime prevention...

Have you let the walls move outwards if so release the rafters and pull walls in to plumb with ratchet strap and refix .If they have been cut wrong then you need to add wood to fix. It may be as easy to strip and start again.

I note PAC 1 comments and did the same, greatest danger is hot stuff falling on floor and radiation on full out put. A relative who is a fire prevention consultant passed it as OK and i have had no problems .The cheap flu (galv.light metal) will not last.

My workshop is quite well insulated but not as well as yours will be, and it preforms as you would expect. heat is retained well and cold does not penetrate that quickly. but there are 24 hours in a day and if its subzero then it will eventually be the same inside, so heat is required and it...

You do not want a bench to rack and move so if the back and ends are filled in and or bench is fixed to shop structure you should be good if that's not possible then you need large sturdy joints.

Concrete slabs 5mm min joints. I have spent quite a lot of time removeing old morter and am power washing . Looking for your recomendation for the best grout that will stay stuck there are lots on youtube etc but i would like your best ideas please.