Sharpening amongst other things
- Thread starter pgrbff
- Start date
Help Support UKworkshop.co.uk:
Jacob
What goes around comes around.
Excellent film!
There used to be a similar hand cranked wheel in every farmyard a few years back. In fact you still see them lying around, unused etc.
Basically for bigger sharp edge tools - scythes, sickles and others. Smaller stuff freehand on flat oil stones.
Sharpening was easy, before it was reinvented by the usual suspects!
There used to be a similar hand cranked wheel in every farmyard a few years back. In fact you still see them lying around, unused etc.
Basically for bigger sharp edge tools - scythes, sickles and others. Smaller stuff freehand on flat oil stones.
Sharpening was easy, before it was reinvented by the usual suspects!
pgrbff
Established Member
There are still many similar wheels around where I live. Some are probably still used. I swapped mine for Japanese water stones.
Jacob
What goes around comes around.
Stropping done with a strop, not a grind wheel. There's a clue in the name.
Either way it's still "sharpening".
It looks to me like they have a piece of leather glued to the wheel. I might be wrong.
It must work for them if they are doing this way, and there's nothing wrong about it, but I'd like to see 'em take a 0.2mm cut off something dense, like bubinga or ebony with that blade
"Sharpening" comes down to shaping the blade, putting a micro bevel on it (optional) and stropping the dickens out of it.
Stropping is not optional, but many folks treat it as if it is. Hence the whole cottage industry of all-in-one tormeks and the likes.
Shaping is almost never required unless you chipped the blade.
Sharpening/micro-bevelling is needed now & again.
For the rest of the time, stop'n'strop folks, stop'n'strop.
I'll shut up now.
It must work for them if they are doing this way, and there's nothing wrong about it, but I'd like to see 'em take a 0.2mm cut off something dense, like bubinga or ebony with that blade
"Sharpening" comes down to shaping the blade, putting a micro bevel on it (optional) and stropping the dickens out of it.
Stropping is not optional, but many folks treat it as if it is. Hence the whole cottage industry of all-in-one tormeks and the likes.
Shaping is almost never required unless you chipped the blade.
Sharpening/micro-bevelling is needed now & again.
For the rest of the time, stop'n'strop folks, stop'n'strop.
I'll shut up now.
Last edited:
Jacob
What goes around comes around.
They not working with bubinga or ebonyIt looks to me like they have a piece of leather glued to the wheel. I might be wrong.
It must work for them if they are doing this way, and there's nothing wrong about it, but I'd like to see 'em take a 0.2mm cut off something dense, like bubinga or ebony with that blade
It's the damp patches where they splashed on some water
That's modern sharpening for you! "Micro bevel" is a recent key term in modern sharpening - good to know they are optional! Stropping is too, depending on the job in hand.
Traditionally, afaik, the micro bevel is put on the chisel blade freehand, which results in a slightly "rounded" shape. It's still a micro bevel, even if the act of putting it onto a blade is not made into a cult.
Cozzer
Established Member
Skill on show.
Bet the bloke could do it all with his eyes closed...
Love the nod towards health & safety at about 11:10 in!
Jacob
What goes around comes around.
The expression "micro bevel" is a new one used by modern sharpeners.
Trad theory never went much beyond the advice to beginners to grind at 25º and hone at 30º.
Then once they got it they could go their own way.
Last edited:
Orraloon
Established Member
Sharpening on woodwork forums has been done to death and I really dont care if I ever see another sharpening video. You should have watched this video however as it showed a real craftsman at work coopering. Always good to see skilled people work. Sharpening to him is just something you need to do to get the job done.
Regards
John
Regards
John
John Brown
Freeloading Social media influenza
Fascinating video. Someone posted another video of olden days coopers in France a year or so back. Impressive skills and very impressive work rate.
I don’t have room for a sharpening jig, I have a bench grinder white a white grind wheel
Dad to day I have three cheep diamond plastic honing things to keep the tools sharp
I keep the oil stones for my carpenters tools
Dad to day I have three cheep diamond plastic honing things to keep the tools sharp
I keep the oil stones for my carpenters tools
Good to see some stropping about sharpening
