Search results

The cast iron table is 1170x800 but the fence runner extrusions and the lock handle for the fence give max overall dimensions that would require a box of 1510x1150 the 1510 could be reduced with a hack saw to the fence runner extrusions also the runners can be slid left or right for particular...

You have listed the correct method the air gap is required to allow any moisture coming out of the breathable membrane or damp coming through the cladding to be dissipated so it should allow water ro run out the bottom of the wall,its not expected to be a large amount and if using feather board...

I understand:- 2x6a alarm&lights, 10a door opener, 16a ultimate dedicated cct. 2x32 ring & spare, thats 6ways/mcbs. But you need a 63a 30ma rcd (2ways). Thats a total 8ways and no rcd was mentioned in your proposal. The box i propose would need a extra 10a rcd but the electrician can wire it as...

If your not sure list what you need to feed. Or PM for phone number.

Not correct yet you need a rcd (2 ways) then the mcbs (1 way each) davy_owen_88 post has the info for cct requirements the price looks typical though. If your not sure list what you need to feed. Just found toolstation 71165 10 way split load box with lots of mcbs page 219 £38.98 easy to...

When i look at the pictures the word precision comes to mind every thing is spot on even the fixings are all positioned the same, nice job. Regarding the lack of breather membrane i do not think any harm to the structure will occur if you let it dry out after fully waterproofing and before...

Remember you can go back to a set up before the faulty driver when everything worked correctly its a part of windows xp & vista, just the op system data stays the same but the java update will come back again.

Nice to see some one else has trouble remembering stuff. https://www.ukworkshop.co.uk/forums/viewtopic.php?t=17323&highlight=

This is very difficult tools and equipment tend to be gathered as the need arises. A pillar drill and a drill driver will get a lot of use as will a bench and vice. Mitre saws are useful but cross cuts can be done on the table saw if suitable. The trouble is all this kit fills the space so...

I had this on file it may help:- http://www.stapeley1.plus.com/odpm_breg_029960%20elec%20regs.pdf

My setup is a compressor from aldi with all the extra bits and a axminster nail gun because you can adjust the depth you sink the nail head for different materials and applications it works well .

That could work but if you do look at the arrangement to expand the bar i would expect that only the top could be machined with out affecting the expander and other fittings may have to be cut also.

I have some deflection but not 1mm so how to correct this :- new bush made to fit, tin the old bush and file to fit, shim using feeler gauge to get correct fit. I mentioned before tighten the chuck or the auger will push up and loose clearance and give noise and heat its worth a check .Also look...

http://www.cclveloduct.com/ Cheaper and always helpfull ask for a discount.

Its working now.

I have this m/c also its good and is complete with chisels. tighten the chuck up well and set the clearance properly and it should serve you well, i did have to fix ply + shims (paper) to the fence to make it straight. For extra depth cut from both sides and set chisel to discharge into the void...

I did the draws last and used the router table to make the joints etc and had seperate front plates to make lineing up easy.

The tv program The House that John Rebuilt (john revell on discovery) covered this problem from memory scarfing in and stainless rod with injection resin glue were used as the oak had gone very hard.

I have one and i am testing it by sending this post please PM with delivery details. I am useing a netgear router and filter the plugs are the same on each end of the cable.

Does this help http://books.google.com/books?id=NUiVuN94GCEC&pg=PT69&lpg=PT69&dq=standard+architect+vehicle+dimensions&source=web&ots=Txk7I5bBTi&sig=qVclk3e55EsXhzbnrM3X1yqGQ5I#PPT69,M1