Search results

I have always understood that the stress is in the bottom part of the joist so thats where the support is needed, think joist hanger and were the rebar is in a lintel. so B would be the strongest .

That guide assembly looks easy to make out of hardwood .

What i did and its not perfect is make a platform on casters remove the 4 legs so the saw sits on it and then locate it with strips than seal it. I then took off the plastic outlet and turned it end for end and rotated it 180 deg. so when connected to the extractor the 1 inch t facing down with...

http://cgi3.ebay.co.uk/ws/eBayISAPI.dll?ViewUserPage&userid=dragong3 does this help

If its a open box a large heater will be trying to heat the world so i suggest the smallest heater in the range (nice and portable)forced air ideally to be sited at the point of need and only run as required hiring in should be considered as once the box is closed its a completely new heating...

Update:- the movie chanells (subscription) are in dd mostly. box office is dolby surround .

In my opinion you could run a additional 2.5mm connected in parallel with the existing so total 5sqmm the consumer unit needs a extra 16amp mcb and a 40amp rcd that will protect all your circuits . thats 2 ways rcd and 1 way each 6a.20a.&16a total 5 (8 ways nearest box size ) and you will have...

ivan has covered everything but the few mm movement should be looked into, you have the machine i am sure you can solve it .It may help to take off the table and make up a suitable straight edge to clear the metal casings when checking the wheel alignment and don't forget to tension the blade...

Mine arrived tuesday.

Yes thats helpful looks like i shall have to buy a movie of sky or subscribe.

Got sky+ and connected up with optical cable to 5.1 amp but which programs are in dolby d it does not tel me in radio times where can i get this info. I want to check i have set up the onkyo amp properly, however i am getting prologic 2 sound ok.

I had a problem with one (on all the time) so i e mailed the service centre got a reply in english and a replacement in the post so the 3 year guarantee does work.

The best are clear (no defects) and there cut to a taper so they look good. There are also shakes which are not tapered but look better on a large roof.

Regarding the out of hours contact i wonder what you would do if work was hard to come by if we were in say a recession. Its been 15 years since the last one so the next can not be far of. Personally i like to be told where i stand when trying to arrange for work to be done so i can make other...

On the couple of kitchens i have done they required lots of electrical relocation so i did it first but with part p thats not possible. Put simply you need a electrician and they make a mess cutting and burying into plaster etc better and quicker i think if the new units are not fitted.So my...

95 degree hinges.

white_sw I think you did not read the instructions 3 are switches 1 is a dimmer and has to be set up differently (you think its dead) so you have done well and have 4 switches.

Just of the top of my head if you cut up large widths of sheet material then put them back together along a straight edge you can get your 90 cut perfect and you have 2x90 set up pieces. Then you expand this idea still using wide sheet for accuracy to set the angles you want and use these set up...

I notice you follow the wood wisperer he uses staves (wood lengths with parcel tape on one edge) to align strips for glueing (the kitchen cutting block) this could be worth a try when next doing one of those stressful glue ups.

I have the SIP saw but they look the same in many ways, the spanner is 24mm . thats actual size across the flats i got a silverline combination spanner of ebay but the nut does not need to be very tight . Glad to see you have fettled the saw to your requirements it looks at home in the shop.