Search results

I have the SIP saw and purchased a spare knife which i cut down to just below height of the saw its no problem then just takes set up time.

Polystyrene is cheapest with vapour barrier applied over studs and poly on the inside, plaster board cheapest use a screw with cup washer to mark top middle of each stud for later fixing of cupboards etc. http://www.fortimber.demon.co.uk/matrl3.htm

For sale on ebay new £110 i have one its quite large but it does a good job and i am pleased with it, sanding discs from axminster. incidentally there single disc version of m/c is £152

Have a look at bookdepository.co.uk they can be less expensive if you have the details to find the book in there big list.

Just found this info it could answer my question http://download.zonealarm.com/bin/free/pressReleases/2008/LossOfInternetAccessIssue.html

The wifes computer stoped working on the net so i have disabled auto update and restored computer to yesterday all ok now, but how do you find out when microsoft have resolved this problem please.

The rip blade in the table are the teeth 'thicker' than the riving knife (looks narrow kerf )if not the blade is no good for that m/c . other blades look well used and need resin removing , have a look at this site for blade usage info. http://www.summitsawblades.co.uk/saw_blades.htm

A modern installation is properly earthed and protected with rcd and 'fused' with mcb,s extra protection by materials and positioning is provided in wet areas this all adds up to a higher level of safety for the user.

11mm osb is firm enough but its not a lot to hold a screw a good method is to use the french cleat system screwed into the supporting batterns at 400mm spacings,50mm insulation thickness min. weight is a consideration for ceilings so plaster board 9.5mm probably easy to put up or thin ply...

Forget the floor its difficult to do after construction for the walls and roof you need insulation with foil backing to stop water vapour passing through it or insulate between studs then apply a vapour barrier which is usually boarded over for protection and looks.

I telephoned record recently the lock on the bandsaw fence was not very firm needed a small part and the upper back stop on the blade was not running true, i was sent a new compleat fence and a back stop, just asked for postal address no problems. Capacitors fail in electrical equipment quite...

Looks like i missed your point ,when a motor starts up it can look like a short circuit until it gets moving (movement generates a flux that reduces its current requirement ) so inertia and load come into it . A practical example my sip saw 2200w (3hp) will start and run on 13amp but only a few...

Watts= Volts x amps ok for rough calculations . 2000w = 240 x ? so its 8.3amps which is no problem. 3120watts is your max .Note also 1 horse power is 746watts. Any conversions just put in google.

Not a electrician but the dist. box has the capacity to feed 4 three phase supplys extendable and as one 3 phase is three single(240v) lots of 240v. At the moment looks like switches for 2x3 phase and 2x240v it needs sorting out lots of safety issues i would make it a priority.Money to be saved...

The elf has datum line along bed, on tailstock and on the swivel castings. the machine is fine for small stuff but you can get ribbing in longer jobs if you are not a expert with the chisel.

One idea would be to bolt treated timber through a dpc strip to the edge of the base so the panels will discharge water just clear of the base to keep it dry so minimal/no damp will come through it and can be dealt with by a proofing of the floor if its required. Turn by the raven pub for...

Its a good idea this info could help. remember you will need 'bent sheet at the junctions eg roof to gable sle do these. http://www.slecladding.co.uk/contents2.htm#steel this info may help in any calcs. for purlins etc page 68. http://www.stapeley1.plus.com/build%20regs%20&%20calcs.pdf

I have the elf and vibration from the way the motor is mounted is a problem i have had to put a block of wood under it. http://www.stapeley1.plus.com/In%20%2022.05.08.jpg

Jigsaw approx £134 or bandsaw ebay link

Freesat box can be connected to the sky dish and lnb to receive same as digital terrestrial tv and the bbc and itv hd channels all free just the cost of the box. http://www.freesat.co.uk/ its just come on line humax do a box . When i upgraded to sky+ i installed new trunking along side the...