Workshop flooring
- Thread starter Matt99
- Start date
Help Support UKworkshop.co.uk:
Gerry
Established Member
Very bad, Get some sawdust on it and it will be like an ice rink.
Gerry
Gerry
I’ve got laminate over chipboard. Works fine, no traction problems, and wheels run easily on it. Easy to sweep, and easy to install.
Vinyl planks - doesn't matter so much if they get wet. Most laminates will be ruined if you have a major spill.
Adam W.
A Major Clanger
I find that shiny floors are rubbish if I'm hand planing, as they are too slippery.
I have a wood floor, probs a similar finish to laminate. Can be a skating rink with fine dust, bit never caused me an issue. In a pro shop I’d avoid in a hobby shop it’s personal preference, personal I like the floor appearance enough to manage the dust/skating issues!
Cabinetman
Established Member
2 or 3 coats of water based polyurethane floor varnish on OSB, looks good,very practical good to wheel equipment on and lasts for years. Ian
JDW
Established Member
I've been looking at 3mm rubber matting to lay over the osb in my new workshop, I had thought about varnish and now I think you've convinced me. Do you use a hard wearing exterior varnish or just bog standard puv?
I've got some old fitted carpet over my concrete floor. I find it much less tiring on the legs and feet, deadens the noise of the machinery considerably and cleans well with a shop-vac.
stuart little
Established Member
I have a laminate sawdust skating rink. I did try carpet on top, but it tended to reeve up in front of castors acting as a brake & collects too much dust/chips. It's been down for at least 10 yrs & now has various paint, glue etc splashes which tend to reduce the slipperyness. Any thoughts on a coat of floor paint, anybody?
Distinterior
Established Member
Exactly the same here!
HamsterJam
Let’s take it apart to see what’s inside….
I’ve got bare chipboard flooring while I decide on a long-term finish.
Did wonder about a carpet off cut.
Has anyone tried any interlocking floor tiles? They seem rather expensive - are they worth it?
Did wonder about a carpet off cut.
Has anyone tried any interlocking floor tiles? They seem rather expensive - are they worth it?
robgul
Barry Bucknell is my hero
Yep - I have "studded" style interlocking plastic tiles - admittedly it's only about 2/3 of a garage and I got them for nothing when the bike shop I managed closed down - we had them in the workshop area and they worked well, with grease and other muck easy to clean - and non-slip with sawdust. They are also more comfortable on the feet than the bare (painted) concrete in the remainder of the garage.
Beware - some of the interlocking tiles sold on ebay and elsewhere are material like a wetsuit, a sort of slightly harder neoprene .... rubbish, at least the ones I have seen. Mine are quite hard plastic (probably recycled?) and have to be cut with a saw.
I did consider them but it would cost over £700. Might stick with the osb whilst I decide
okeydokey
Established Member
If your floor is pretty good then consider used carpet tiles from the bay, they are usually ex offices and come in various grades so if you don't mind coffee spills and wear and not fussy about colour or pattern they are pretty good for this task. Spray glue them down and they do the job, don't wrinkle as you move stuff around - but if one did dislodge then spray glue it down again.
I have good quality yoga mats in front of the lathe, and main workbench does save your feet and easily cleaned. Don't use the cheapo foam ones, they just disintegrate, DAHIK.
deanclarkewilliams
New member
Forbo make Flotex Carpet. It comes in 2mtr wide rolls and is very durable. You can remove most things from it including oil and paint with a scraper while it's still wet. Reasonably priced too.
