Steve Beck
Member
I have two old round head lignum vitae mallets which I have used for years. Thinking about making a square type headed mallet. Open to ideas and photos of your favorite mallet.
Wood mallet
- Thread starter Steve Beck
- Start date
Help Support UKworkshop.co.uk:
Ttrees
Iroko loco!
I like this one for light work, made from mock orange
This one for medium jobs, probably where the mallet you are thinking of making
would be best.
It's ok I suppose
But my favourite is this Thor one, which is the plug thumper
Great yoke altogether
Tom
This one for medium jobs, probably where the mallet you are thinking of making
would be best.
It's ok I suppose
But my favourite is this Thor one, which is the plug thumper
Great yoke altogether
Tom
TheUnicorn
Established Member
I was given a load of 18mm ply scraps a while ago, just for the hell of it I made a few mallets from it, obviously ply is not ideal for an edge on impact, that said they cost me nothing and have had a good bit of use. My favourite of the ones I made had a short handle and a heavy curved head, so in use you don't have to swing it hard to get a good clout, all the swing is from the wrist, so good for chisel work. I think I based it on this youtube video, though mine has a shorter handle
I think the key is to get the shape of the head right so that you are hitting the chisel as close to 90 degrees as possible so as not to skew the strike
I think the key is to get the shape of the head right so that you are hitting the chisel as close to 90 degrees as possible so as not to skew the strike
Last edited:
GCM
Member
I made this one (actually, I made a few in different sizes!)
Made from scraps - oak and an unidentified heavy dense wood...
I weighted it with molten lead (used solder from my stained glass projects) which give it a nice solid weight.
Made from scraps - oak and an unidentified heavy dense wood...
I weighted it with molten lead (used solder from my stained glass projects) which give it a nice solid weight.
Last edited:
For donkey's years I used a round "carver's" style mallet for dovetailing & mortising & was perfectly happy with them. Then for no particular reason, I made myself a "square" mallet with a head that weighed around 450g (close enough to a pound in old money). After a bit, that became my go-to mallet for D/Ts & mortising, & now I find round mallets less desirable; I can direct the blows more precisely & sharply with the hammer type. But it's what you like & what you get used to, I cannot see an overall advantage in either. I advise experimenting with different sizes/weights of head to see what suits you best. That's easily said for me, living in a land with abundant scrap hardwood with densities around 1.0, which gives you a hefty, but compact mallet. (Also makes it easy to calculate a rough weight for a given set of dimensions).
I do like a decent handle with an oval hand-grip to help feel where the thing is going. I can't be bothered faffing with off-centre turning so I turn my handles from a blank with a rectangular cross-section, then work it oval with rasp, scraper & sandpaper. It's actually quicker than mucking about changing drive-axes.
I've got all sorts of sizes, for all sorts of jobs & because it's easy to replace a head or make a new mallet, I'm not too careful with some of them - they get treated as "consumables". This one has had a bit of a tough time & about to get a head transplant:
I've tried different angles on the faces, & settled on about 5* as suiting me, but mileages vary on that score.
Mallets are pretty easy to cobble up, whether you chop out the handle hole or laminate the head, so make yourself a couple & see how you like them. They may grow on you or you may go back to your round jobs - whatever works for you!
Cheers,
I do like a decent handle with an oval hand-grip to help feel where the thing is going. I can't be bothered faffing with off-centre turning so I turn my handles from a blank with a rectangular cross-section, then work it oval with rasp, scraper & sandpaper. It's actually quicker than mucking about changing drive-axes.
I've got all sorts of sizes, for all sorts of jobs & because it's easy to replace a head or make a new mallet, I'm not too careful with some of them - they get treated as "consumables". This one has had a bit of a tough time & about to get a head transplant:
I've tried different angles on the faces, & settled on about 5* as suiting me, but mileages vary on that score.
Mallets are pretty easy to cobble up, whether you chop out the handle hole or laminate the head, so make yourself a couple & see how you like them. They may grow on you or you may go back to your round jobs - whatever works for you!
Cheers,
Phil Pascoe
Established Member
all round mallets for me - nothing of the flat faced type. One of verawood for heavy work (ouch, my ears) and a couple of urethane headed round ones.
The rectangular type are so quick to make that you should just make one fast and then see what you don't like about it and correct it on the second one, or trim/change the first.
The rectangular type are so quick to make that you should just make one fast and then see what you don't like about it and correct it on the second one, or trim/change the first.
Steve Beck
Member
I've always fancied making one of those gigantic mallets they used in circuses and the like to bash in big marquee pegs. 5' handle and a sectional head at least 8" in diameter wrapped with brass or leather strips.
Phil Pascoe
Established Member
That's a "beetle".
Brill88
Tom Brill general woodworker and woodsman
I've always fancied making one of those gigantic mallets they used in circuses and the like to bash in big marquee pegs. 5' handle and a sectional head at least 8" in diameter wrapped with brass or leather strips.
I use mine I made from elm for hedglaying
Attachments
dannyr
Established Member
I suppose you just get it out of your bag and the hedge gives up and lays down?
(or is it for the vertical (or angled, depending) poles)
big-top mallet, beetle, commander or maul -- any difference?
Brill88
Tom Brill general woodworker and woodsman
Brill88
Tom Brill general woodworker and woodsman
Beetle is the traditional name I think timber framers call them commanders and for fence posts mauls or mells but metal onse around 12 to 14 pounds that look a bit like a sledgehammer but with large faces either end
dannyr
Established Member
much respect -- nice job there
Brill88
Tom Brill general woodworker and woodsman
Cheers not always as nice as that usually rough old buggers
Nice job! Live hedging, just took me back to a different life there for a moment. Been years but the Elwell still sings for battle!
I use a Thor hide faced mallet (no 3) because I like a heavy hammer but I cut the handle down. It works well for me, like a cross between a carvers mallet in the hand and enough weight to smack the holdfasts down with no effort. 'Don't hit it harder. Get a bigger Hammer'. For really light work I have a brass jobby that I bought when I was more impressionable and a traditional wooden mallet in disgraceful shape I've had since I was a kid. Keep meaning to cut it down to sort it out but I never do and just hang it up again.
I use a Thor hide faced mallet (no 3) because I like a heavy hammer but I cut the handle down. It works well for me, like a cross between a carvers mallet in the hand and enough weight to smack the holdfasts down with no effort. 'Don't hit it harder. Get a bigger Hammer'. For really light work I have a brass jobby that I bought when I was more impressionable and a traditional wooden mallet in disgraceful shape I've had since I was a kid. Keep meaning to cut it down to sort it out but I never do and just hang it up again.
Last edited:
Those cheap cheerful beech mallets become a far nicer tool if you just take them to the belt sander and knock all the square edges off.
