Search results

Here's a fence I made when I got tired of the original router fence from Ryobi MDF, a bit of "formica", some scrap plywood and a few "T" rail bits. Clamps to the rip fence on my Ryobi 10" table saw. Got the plan from "Wood" magazine (US) Works well, great improvement! sam :-)

Richard - I keep seeing you everywhere now :-) sam :-)

Paul, Thanks for the interest! Here's a few pics of the completed table. It's from plans in July 2004's "American Woodworker". White oak with wenge accents. (They were supposed to be ebony but I couldn't find any) The table is in the American "Arts & Crafts" style, particularly from the...

Yes it's a back bevel - just like J's explanation. We're talking 10 seconds on the stone. Just enough to take off the wire edge. I'm not sure if this has cropped up in this thread, but when you get to these very small sizes, flatness of stones is important. Cosman flattened his stones against...

Yes - and to be fair, I'm sure he mentioned that at the time. sam :-)

Going back to the wire edge:- I'm still new at this sharpening cult (woe is me saith the apprentice!) but what I've picked up I got from Rob Cosman at a course I attended last summer. He was using (and so am I now!) Norton water stones. To get the wire edge off, after honing the...

Matt, I'm new at this too, but didn't have the problems you seem to be having. Here's my recent experience: I used dewaxed blond flakes in a 1lb cut. That's pretty thin, but as I was new at this I thought it would give me a bit more flow and increased drying time. (That's a 1:8 ratio of...

I'm a bit late with this one! Yes of course the slots should be parallel to the blade. Otherwise - what's the point? I use the slots & the sliding table. sam :-)

Woody, I don't usually gloat, but I've just been to Lee-Valley in Calgary, Alberta. This lot cost me 119.82 GB Pounds. Sorry, I couldn't resist! sam :-)

Well I went to the through wedge tenon demo yesterday - again money well spent. Although I've done machine mortice & tenon joints before - a lot of tips & insights that I'd spend years learning by myself. Came away with a #140 skewed block plane Alf. Spent last night putting a black walnut...

Thanks for the replys & the advice. I went to the demo - yes it was Rob Cosman. He spent an hour talking & demonstrating sharpening. Worth it just for that. When you're doing all this in isolation & just picking stuff up from books & forums, it's nice to see & be able to ask...

OK you lot, I've been reading this forum for quite a while now & you've sucked me into this plane cult. I've told my wife that it's not my fault; you guys are the real problem; isn't that why we emigrated anyway? She's not buying it! Anyway, I've recently purchased a Lee Valley 4 1/2...

Here's a few I made for Christmas presents!

I just finished my 10'x18' deck yesterday. I already had a Porter-Cable "pancake" compressor & 18g nailer that I use for general furniture making. They were on sale for $279 Cdn a while back. (That's 120 GB pounds). I found a cheap (Chinese) framing nailer for $148 Cdn (63 GB pounds). I...

I've got a Laguna LT14SE which I consider to be a high quality bandsaw. I resaw a lot: maple, walnut, birch, cherry, ash. The cut is very smooth & accurate (for a bandsaw) but as Aldel & the rest said, not as good as a tablesaw & still needs at least 1 pass through a planer. sam :-)

WIZeR, If your interested in prices for decking wood over here, I'm just into replacing my deck & was pricing up the stuff yesterday. Here's a few examples of what it costs over here. Here is Canada (Not US) / Exchange rate is about 2.36 Cdn$ to the GB Pound. - Treated 2"x6" x12ft joist (fir)...

I was under the impression that the whole bunch - Porter-Cable / DeWalt / Delta were now owned by Black & Decker (exit stage left feeling sick!). Isn't that right you guys down south? (Sorry Noel, I missed your post!) sam :-)

Chris & Noel, Yes it's on 6 castors. I chock it up on 4 wood blocks when I use it. It's real heavy so it doesn't move. It's birch ply with birch facings & trim. The top is Canadian Maple. Not cheap, but you only do this once! The top is 2 1/2" thick. laminated from 1 1/2" wide maple strips. I...

Roger, I had the same dilemma 18 months ago when I started getting into this hobby. I didn't know enough to know what I needed, but I decided that building the bench would get me well & truly "in at the deep end" & give me lots of experience quickly. So I picked a design from a magazine...

I've been at this hobby for about 18 months now & I'm starting to look at my hand tools. I've got an old Stanley type plane; I've got the Japanese water stone & got into sharpening theory & practice; everything is ticking along nicely, OK so far... But! I have this niggling urge to try an...