Search results

Take the filters off, fit the mask, cover the filter holes with the palms of your hand and breathe in. If you can't it fits fine :)

Seems obvious to me!

https://www.trenddirectuk.com/wp-snap-d-35r https://www.trenddirectuk.com/wp-snap-d-964 https://www.trenddirectuk.com/snap-db11l-5?___SID=U https://www.amazon.co.uk/d/Drill-Bit-Se ... brad+point http://www.ebay.co.uk/itm/ADDAX-15-PCS- ... SwLzdWS9If http://www.ebay.co.uk/itm/5Pc-Titanium-...

Too complicated for me I'm afraid but found a photo, uploaded it to stencilgram.com and worked from an image of that. Its rough but might do for a practice one.

In reply to my own post for future searches... Physically it measures approx 45 x 90mm, jubilee clipped to motor with mounting spacer. sealed with flying lead. 25uf 400v 50hz - see pics Also found a wiring diagram in the switch box pics att.

I will reply to avoid speculation. As I believe you are aware Keithie had some issues with the moderators and is now no longer a member. Thanks for your interest, but no further discussion will take place on the matter.

https://www.amazon.co.uk/d/Electrical/E ... gy+Monitor

Yep, thereabouts. It'll probably be 18 or 19mm but you get the idea.

Very generous of you to say excellent :oops: but I'll take it :) If its a line cut thing like the beetle and mini I did you effectively need to create a stencil, making sure that there are no portions unsupported, and you'd need to remove a fair bit of detail but keeping the obvious Duke...

As you have it in your sketch. The one on the back to stop the side to side tilt, the two (just for aesthetics you could use one central one) front to back to prevent tilting forward. you could also of course use a bit of the 2x2 at 45 degrees instead if that looks better. As a thought you could...

two right angled triangles back to back excuse the very rough sketch

If they're effectively constrained between wall and desk then yes, a bit of 2x2 will be man enough to hold your 15kg and a simple half diamond on the rear and two triangles on sides from something rigid like ply or mdf support the top and bottom plates (if you don't have the brackets in your...

IMHO They will be highly unstable and susceptible to being knocked over, especially with 15 kg on top. And they look really (too?) tall. Ideally a speaker stand will have lots of mass and put the tweeter at around eye level when sitting in your chair. Make the centre section of your stand a...

I would imagine that setup would cover all eventualities that you may need but afraid I can't offer any advice as the badger is the entire sum of my experience with airbrushes.

Yep. With this cheap set, the pots have separate lids, so if you get a few extra you can leave the paint in the pot and replace the screw cap, and just use another for the cleaning. Again because of the basic design there are no needles or jets to worry about*, so just a quick shake and squirt...

Mine is about as cheap as one gets, around 25 quid for the 'set'. It comes with a little aerosol propellant and fitting so you can use it without a compressor, but they do not last long, so I just bought a separate adaptor for about 3 quid and run it from my mickey mouse lidl compressor. It...

They're called Cross refills or Cross style, available at most stationers and Amazon etc.

To see what the usual joinery wood species look like together have a look at some of CHJ's segmented pots, usually oak ash walnut beech cherry etc. for example http://www.quest42.co.uk/woodwork/html/page30.htm

It would probably overheat and melt. 25w seems awfully small for a pendant lamp though.

Please no references to the above thanks. Just continue to help the OP and put the thread back on topic.