Search results

I'd like to try and come along if thats ok. I'd like a quick lesson on spraypainting MDF if thats possible. I'm afraid I won't be bringing any expertise with me, but hope to leave with some! Regards Andy

I might be able to give you a hand as well!! The problem is that I can only get over in the first two weeks of June! Strange coincidence eggflan

Another PM sent

Could the forum give me an idea of how much it should cost to get planer blades and saw blades sharpened?

I'm sure I saw something similar on (I'm sorry I'm about to say this) QVC, last Sunday. You might have to look at their homepage to find it. If they do have it, at least you can send it back if its no good, after you've tried it

Wow, another fantastic job. What is a honed granite work surface, compared to a polished one?

Hi Woodchip, have a look at Pickards Hardware, in Keighley. They might be able to help.

As it was a lovely day, I decided to take my wife out for tea and biscuits,to a nice little tea shop, just outside of Skipton. At least this got her in the car. It didn't go down well, when she realised she had been conned and we ended up at the British Hardwoods one day sale, where there were...

I've been looking for a range cooker for my new kitchen. Before the VAT reduction the price was £1050, after VAT reduction the price is now £1085. I think I might wait for the sales, I might get it for £1100 if I'm lucky

Can anyone explain how you know if you have the right needle size for your finish, when you're spraying. What would be the problems you would have if the needle was too big or too small for the finish you are trying to spray. I'm going to try a earlex 5000 hvlp system, which comes with a 2mm...

Just a reminder that the woodmex 2008 show runs from the 26-29 Oct at the NEC Birmingham. Looks like quite a large exhibition. There's also the Interbuild exhibition on at the same time held in neighbouring halls. These are both free entry if you register as trade before hand

Please tell us all about it!

Very nice looking job. What finish do you use and is it the same finish on the inside of the cabinets as the outside?

First of all, a thankyou to ByronBlack for posting my photo's. The incra fence is a massive improvement on the original fence, in my view. It wasn't bought with that use in mind, but for a separate router table. I've only cut panels on the saw yet so have found the longer fence better. I guess...

I've taken a couple of pictures of my ts200 set up but have no idea how to up load them onto the site, even after reading the FAQ's. Will try again if anyone can explain in plain english

I've got the same table saw but thought the steel extension table was rubbish as well as the fence being too short. I've made another extension table out of MDF and stuck some laminate on the surface. I've picked up a second hand incra ls positioner jig and set that up to act as a fence for the...

I rang Apollo up and basically you need the gun that came with the system. They haven't sold that gun for sometime and have a new gun out. This doesn't work as good on the 700. I've tried a different hvlp gun but without success. I've therefore sold it, as I seemed to be wasting time and money...

I've aquired a secondhand Apollo compressor, but without the dedicated spraygun that comes with it. Would any HVLP spraygun, work on this compressor, or do I have to buy the Proline one which fits the 700 model. If anyone has any technical information on air consumption or operating pressure the...

I have just fitted the same router plate and have the same problem, with a 1 to 2mm gap larger than the plate. I've seemed to have solved the problem by putting the plate in place, with router attached, and filling the gap with a decent wood filler. I've left it over night and now there's no...

Is there enough glue on the strips to stick them to the panel. I only ask because I'm in the process of having a go at some similar doors.