Search results

Looks much better, personally i would move the pillar drill ( Note that the pillar drill can work quite well with the chuck at your eye level) to adjacent to the lathe, shortening the lathe bed to provide space. This will make the bench more versatile especially with longer timber (garage door...

The storage racks take up space reconfigure for more floor space use walls above eye line .The use of casters under machines is good and creates versatility .Look into making the garage door open able so that machines can be put out side to create floor ,bench space and ability so handle long...

Most of the heat will go through the roof what have you done to address this. All so if the 25mm insulation in the walls is fitted tight with no gaps or gaps are foam filled whats the problem your insulated.

You will probably want to strengthen it by inserting panels or cross diagonals on three sides unless you can attach it to the workshop wall in a fixed position, the rest looks ok for a starter. workout the costs and check if its large enough for your purposes.

The arcing will have overheated the armature and caused the solder to melt and could have been spun off . Brushes are not expensive and you can make the wrong size fit by cutting ,just to see if it will run ok having cleaned the armature segments.If not new armature and brushes .

The usual procedure is to determine which circuit is causing the trip so switch off all but the lights and if no trip, on with the ring main if that trips unplug everything if good, start plugging back in till trip. there are other possibilities/circuits that i am sure you can work out. So if...

If the door does not close properly it will be a impossible task to desiccate/dehumidify the container . I still recommend insulating the internal side of the roof just stick it on with nonails type adhesive and fill any joins with foam its got to be least expensive option then heat or desiccate...

Insulate the ceiling and get some heat in there, also check out the ventilation especially if you have a wood burner.

Petrol generator say £120 and construct a weatherproof housing. Just run when you need it.

Its a safety feature to stop a slack nut flying off .You loosen it twice so that it is properly slack if it still sticks then a slight tap side ways or on the end (not the sharp part) will get it loose

Just keep the existing arrangement then extend the ring main, cooker and the lighting circuits when you renovate the kitchen.

I used a inexpensive in line all plastic unit mounted on a board and sat that on four car cleaning sponges this eliminated any transfer of vibration its very quiet. I also used insulated flexible ducting to minimize any condensing of the water vapor and reduce noise and a induct flap one way...

The wheel on the right hand side is used to tilt the blade when the lock screw is released (on front face) .Inside the saw its long screw has a adjustable stop clean/adjust this to get 90 degrees.

just a question if you install a earth rod at the shed and use the swa as a earth conductor could you not double up on the live and neutral ( with correct colour sleeves ) and have half the volt drop.

I would mount on a plastic box then surface mount on the wall .

If they have one out of the box check for play in the quill in a number of extension positions if its very loose leave it, think about drilling a hole with a fine drill its going to be to large

Ebay member woodnducks44 Colin Evans hoursmans green Wrexham rd. sy13 3bz 019480830593 has all sorts of machinery from time to time

Could you make doors say 2 inches thick that could then be clad at a later date to give the look you want.That could be a cost saver and minimal double work.

Just a suggestion have a look at my post using two compressors which you could arrange to only switch on the second for heavy air requirement so ok for number one to auto cut in while using a machine.I would say that my choices do not have the machine quality you were proposing but there are...

Current rating :- approx 4.2 amps equals a kW. also 746 watts equals a horse power so you can calc kW for the above TLC calc. You can Google current rating, how the cable is installed and there for its ability to loose heat is a factor on current rating.