Search results

Home made shed with flat roof ( 1 in 40 fall left to right )felt sealed to existing ,water off half the original shed will flow over flat roof to re positioned gutter .This only works if it will have sufficient internal head height.

The axminster cat lists 3mm thick blades if the riving knife is thicker you should talk to them.But first check its in line with the blade and not off set . I like CMT blades others have other preferences .

Check you are drilling at the correct speed. http://www.raygirling.com/dpspeed.htm Pillar drills speed is adjusted by moving the belts on the pulleys

The differential pressure switch seems to be operating ok . Toolstation sell the oil .Draining the tank is a good idea .It can be used for tyres, blowing away dust and chippings and nail guns ,Aldi sell the bits for the above from time to time.

No its just the loft.

The bathroom ceiling has 10 inches of insulation over it is it ok to fit down lights and drop the insulation over them. I am concerned with the heat they give off and undecided on 12volt or mains also some would ideally be able to adjust the beam angle any help would be appreciated.

It had a small fit ,you can recover to a previous good condition but its minor. I think you should switch windows up date back on its mostly security and you use the net and of course you can go back if you need to very few have problems and there mostly hardware showing they need attention.

From your reply treat the first 3 feet as direct lay on concrete and have the firings made to 14 feet to level the rest it keeps it simple and inexpensive. One 14 foot 6x2 will give two firings re treat cut edges.

Your post is difficult to understand a picture may help, my interpretation is you have a 17 foot concrete floor with a estimated 1 in 40 fall so you could just live with the fall. Or lay strip dpc and firings 17 feet long (wood yards will cut them) screwed to the floor then moisture resistant...

Toolstation have a grasslin page 306 at £28.76

Is the expansion due to water vapour coming through the deck and being trapped by the felt. I had a flat roof applied to my shop recently they used felt with large holes all over it then hot mastic for the next layer which flowed through the holes and it was then stuck to the deck with dabs that...

Have a look at my previous post https://www.ukworkshop.co.uk/forums/viewtopic.php?t=34247&highlight= I did not bring out the point that its a second phone line of high quality and i now have two instruments connected to the router one each which give two outgoing lines but only one incoming...

I have had some good results by retuning with the ariel disconnected then reconnecting and tune again also some equipment (humax box in my case) can be given a full reset via the menu and then retuned.

Just a update on my deliberations, the combi is out. Had a plumber visit me last night and he pointed out the water pressure was marginal and we would have to learn to live with the time lags.So as the bathroom needs the extra space we have to reposition tanks and cylinder and take the...

This is hard to explain,cast the half circle first .Shutter across to form the base of half circle top of shutter at FFL. Then fix a battern around the half circle with its under side at FFL get a board to scratch off and cut a notch same size as battern so the board ledges on batten and rests...

I would concrete it ,smaller stone with compacted sand over the rough hardcore to level then lay thick poly, to damp proof ,four inches of concrete over that if you have space so the floor will not be to high put insulation (polystyrene)over the poly. then the concrete. A wood floor is same as...

Removing plug reduces load on starter motor so it spins faster reduces volt drop and helps it to start thats my suggestion. It may then start normally once slighty warm on the one cylinder.

woodbloke Sorry for the confusion i have edited my post.

Calpol I think a picture would help a lot here your answer was not very informative.

What do you mean nothing there, is it compacted earth is it flat and level does it get damp, the size . i think we need more info to suggest something that will last etc.