Post a photo of the last thing you made
- Thread starter DTR
- Start date
Help Support UKworkshop.co.uk:
Lons
Established Member
First go at a nautilus shell which has been on my "to try" list for a while. Just a bit of softwood to tyry chosen for the grain but it was quite dense and heavy so not sure what it is.
Also a quick rabbit puzzle for my 3 year old granddaughter.
Also a quick rabbit puzzle for my 3 year old granddaughter.
Attachments
John15
Established Member
I like the snail shell Lons - very attractive.
John
John
Ttrees
Iroko loco!
Wow , some great stuff here in the last while ...
That shell is stunning :shock:
Looks like it took some work, Its got me wondering how you done it .
I must say, I never liked the look of knots in pine until now .
Spent yesterday doing something else other than hand planing
and tried a load of tools out for the first time, which I had hidden away .
Reluctantly made a shooting board by hand as I wanted to get my tablesaw commissioned first .
Which involved other rabbit holes like making basic sharpening setup V.2
Everything involves a rabbit hole that I can think of at the moment (hammer)
I spent a good while trying to find a video (At least, I think it was in a video) of someone using a
"speed square" for shooting 45 degrees, which they routed out a dado for the tool to rest in
Just wanted to see it again to get an impression how good it might be,
but got fed up searching in the end .
That shell is stunning :shock:
Looks like it took some work, Its got me wondering how you done it .
I must say, I never liked the look of knots in pine until now .
Spent yesterday doing something else other than hand planing
and tried a load of tools out for the first time, which I had hidden away .
Reluctantly made a shooting board by hand as I wanted to get my tablesaw commissioned first .
Which involved other rabbit holes like making basic sharpening setup V.2
Everything involves a rabbit hole that I can think of at the moment (hammer)
I spent a good while trying to find a video (At least, I think it was in a video) of someone using a
"speed square" for shooting 45 degrees, which they routed out a dado for the tool to rest in
Just wanted to see it again to get an impression how good it might be,
but got fed up searching in the end .
Attachments
Yes, it was on the side of a larger board. Only this small portion was rippled. Is that normal?
It was very tricky to work with, p/t just tore out terribly. Lots of patience with a block plane was needed. But good practice I'm sure!
It was very tricky to work with, p/t just tore out terribly. Lots of patience with a block plane was needed. But good practice I'm sure!
davem62
Established Member
Lons
really like the shell ,the grain and colour make the shape stand out,
david
really like the shell ,the grain and colour make the shape stand out,
david
MrTeroo
Established Member
Ttrees":2l60k5if said:
Was it this? (at just after 7 minutes)
https://www.youtube.com/watch?v=eqWbgkl_ryM
Haven't posted anything for a while.
So,,,, flip top mobile base for the thicknesser. Poor thing is a bit work weary, but it does deserve somewhere nice to sit.
I did make the base big enough to fit a replacement when the time comes :wink:
And, I took a load of this:-
Melted it in the oven, gave it a big squeeze in a mold, of sorts.
Rough turned them into some of these:-
Then I made them into a pair of wheels for my table saw
So,,,, flip top mobile base for the thicknesser. Poor thing is a bit work weary, but it does deserve somewhere nice to sit.
I did make the base big enough to fit a replacement when the time comes :wink:
And, I took a load of this:-
Melted it in the oven, gave it a big squeeze in a mold, of sorts.
Rough turned them into some of these:-
Then I made them into a pair of wheels for my table saw
Lons
Established Member
n0legs":pai2gepi said:
Thanks for the comments guys
Not as difficult as it looks just fiddly, 32 pieces, and sanding was a chore because much of it was by hand as I don't have a flexi sanding pad like the one in the video.
Check out youtube for videos.
Bob
Buckeye
Established Member
Finished this Sam Maloof fish sculpture. I had seen it on the Sam Maloof flickr album and thought I should have a go at that. This is elm from the big house estate next to me.
Roughed out on the bandsaw mostly then combination of spokeshave and rasp then sanding and more sanding. Not bad for a first go, I think I will be making more based on comments and would do things somewhat differently both in design and execution.
Roughed out on the bandsaw mostly then combination of spokeshave and rasp then sanding and more sanding. Not bad for a first go, I think I will be making more based on comments and would do things somewhat differently both in design and execution.
n0legs":84g8ugql said:Haven't posted anything for a while.
So,,,, flip top mobile base for the thicknesser. Poor thing is a bit work weary, but it does deserve somewhere nice to sit.
I did make the base big enough to fit a replacement when the time comes :wink:
And, I took a load of this:-
Melted it in the oven, gave it a big squeeze in a mold, of sorts.
Rough turned them into some of these:-
Then I made them into a pair of wheels for my table saw
what were the coloured beads?
Steve
SteveF":2tz53np4 said:
Cut up, painstakingly I add :lol: :-
Milk bottles, milk bottle tops, coke bottle tops, Tresemme bottles, anything that was hdpe grade plastic to be honest Steve. Quite fun to experiment, but I won't be repeating it anytime soon :lol:
Paddy Roxburgh
Established Member
n0legs":3guipiwd said:
Nolegs, just want to say I love your wheels. I saw a youtube vid once of some american making a mallet from melted down milk cartons. If I remember rightly the vid was quite annoying (they kept trying to be funny) but the mallet itself was pretty cool.
Paddy
