Im off to :-

[Blister]

Hegners on Thursday to Buy some goodies for my VB

and have a nose around the factory while I am there

\/ :mrgreen: \/ :tool: :tool: :tool:

O what fun 8)

 

[loz]

Newsflasgh - Recession over in UK.......

What ya buying ?

 

[boysie39]

Might I be so bold as to suggest that you buy a big workshop if they have one :lol: :lol: You said you havent got any room,or have you had anotther clear out that I havent heard about yet :?: :?:
Car or Van which are you taking would give some indication of what you might be after.Anyway enjoy your day out,no doubt there will be more offerings soon . REgardes Boysie.

 

[stevebuk]

hi blister
any chance of seeing what you do on the VB, not seen any of your stuff yet. :lol:

 

[wizer]

hi blister
any chance of seeing what you do on the VB, not seen any of your stuff yet. :lol:

lol Steve, he doesn't turn, he's one of us woodworkers who just buy and sell machinery :lol:

Allen, can you slip a few rolls of sand paper in you pocket please

 

[stevebuk]

hi blister
any chance of seeing what you do on the VB, not seen any of your stuff yet. :lol:

lol Steve, he doesn't turn, he's one of us woodworkers who just buy and sell machinery :lol:

I did think that Tom, but thought i would give him a chance.. :lol:

 

[Blister]

hi blister
any chance of seeing what you do on the VB, not seen any of your stuff yet. :lol:

Steve

Not sure if you was a member in my turning days ?

Started 3 members on the slippery slope

!st was DaveL

2nd Was John B , but only mainly pens , John already had a lathe

AND 3rd was our very own WIZER

Then along came dads bad health , leading to his death

15 days before he died I was seriously smashed up in a non fault motorbike accident , leading to 10 weeks off work , and over 15 months to get reasonable use of my left arm back :?

Then started the Garage conversion to get a bigger workspace :roll:

And its already too small :roll:

So my ideas of doing some flat work are now out the window unless I move and get bigger workshop space , can I be sr-ed , No , so eventually it will be turning again

my shopping list is for

2 shorter tool rests
Deep hollowing set
no 3 morse taper steb drive
no 3 morse taper revolving center
M33 x 3.5 chuck drive plate
3 more taper Jacobs chuck
and a rubber mat for the lathe bed

And anything else that may take my fancy :wink:

Cant wait to make some mess

PS

if you know anyone who wants to buy a new in the box Jet JPT260

and a new Delta dual voltage 115 / 230 table saw , let me know

I NEED the room

 

[wizer]

I'd love the saw but I can't afford it. Xmas on the way.

 

[Blister]

I'd love the saw but I can't afford it. Xmas on the way.

Turn the wife a earing holder

Give Libby some empty cardboard boxes and shiny paper

Thats the prezzies sorted

Treat yourself to a new saw :wink:

Way to go :mrgreen: :mrgreen:

 

[The Bear]

What model saw are you selling?

Mark

 

[Blister]

What model saw are you selling?

Mark

Its a NEW UNUSED Delta table saw , cast iron top , side extension , on a dual mobile base

115v and 230 volt by swapping some wires in the motor
!.5 HP when used at 115v
2HP when used at 230 v
instruction book etc

£475

looks like this one in the link
http://www.rockler.com/product.cfm?page=18222

 

[Paul.J]

I thought you had a Unisaw :? :?:
That saw is similar to mine Allen.Could you not take the extension bed off cut the rail down to suit,and just use the cast bed part.It is a good saw.

 

[Blister]

I thought you had a Unisaw :? :?:
That saw is similar to mine Allen.Could you not take the extension bed off cut the rail down to suit,and just use the cast bed part.It is a good saw.

I did , but when the Doctor told me I had a nasty illness , I sold it :roll:

Then they downgraded the illness so I purchased this one

Now I have no room :?

So its back to turning only