Search results

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. A

    SCAFFOLD BOARDS.

    Scaffold boards are about 11/2 inches thick and I would like to cut them down the middle to make them roughly 3/4 inches thick. Has anyone done this and what would be the best way to go about it. Thank you for any information.
  2. A

    Plywood for Paulk bench

    Good used scaffold boards and heavy marine plywood.
  3. A

    Help Needed Please! Electric Machine Fault.

    If you know little about electrics get somebody who does know have a look at it.
  4. A

    Can anyone tell me how this table has been made?

    No, it looks fantastic.
  5. A

    Hot Dipped vs Zinc Coated Galvanised Nails - which for roofing?

    Hello, I live on the Shetland isles and due to the weather/salt air all our outside building is done using stainless steel nails. All the builders merchants here keep a huge range of sizes.
  6. A

    UNIMAT 3.

    Hello, Thank you for the information, It was most helpful. I need something a bit bigger. I have a friend who has a Warco 180 so I will have a look at that.
  7. A

    UNIMAT 3.

    Hello, Can anyone tell me how the unimat 3 laths perform on steel as I am thinking of buying one and have found out that the wattage of the motor does not seem very high. Thank you.
  8. A

    LATHE.

    Hello, I am considering building a small lathe and have motor a from a chop saw. It has 4800 on the tag which I assume is the speed of the motor before it goes through the gears. The motor runs ok but I have no way to check the speed. Any advice on speed reduction would be welcome. The motor has...
  9. A

    Knive sharpening.

    Hello all, Thank you for your most interesting views on this subject. I think that if you want a really sharp edge it would be better to sharpen from one side only and leave the other side flat as the angle would be much less than what it would be if sharpened from both sides. I like the point...
  10. A

    Knive sharpening.

    Can someone tell me why some knives are sharpened from both sides unlike chisel which are always sharpened from one side. I would have thought that due to the angle on the finished item you would get a much sharper blade with one side sharpening.
  11. A

    Rust on machine tables

    Try living on the Shetland Isles, salt air everything rusts.
  12. A

    MDF or Ply for the back of a heavy picture frame?

    What is wrong with glass at the back, you could also put something between the glass and the front to take the pins.
  13. A

    Has anyone tried Dewalt 20v batteries on Erbauer EXT tools?

    Yo can get a high amperage 12volt supply from an old computer power supply.
  14. A

    Has anyone tried Dewalt 20v batteries on Erbauer EXT tools?

    A lot of these tools are more than 12volt ie 20 volt 18 volt so a mains power pack could be a good idea, and you cannot always get the correct voltage by cobbling batteries together.
  15. A

    Has anyone tried Dewalt 20v batteries on Erbauer EXT tools?

    If you are only using the battery powerd tool in the workshop has anyone thought of building a mains driven power pack. It could sit on the bench and if you connected/plug in a cable from the tool it would save buying a new tool/battery.
  16. A

    Blade shortening.

    Thank you.
  17. A

    Blade shortening.

    Thank you.
  18. A

    Wooden clock gears.

    Hello, Thank you for the reply. The book is all about wooden clock gear cutting using a scroll saw. I find the CNC machine interesting as I had a friend many years ago who built his own. Can you give me some info on your machine. Do you use a laser to cut the gears or can it be done with a...
  19. A

    Blade shortening.

    Hello, Thank you for the information. I now intend to get some Pegas blades but on looking at them on eBay there seems a lot to choose from, there are spiral once’s as well. As I only want to cut 9mm plywood what would you recommend. Logan.
Back
Top