Search results

I need advice on tools to carve out large asymmetrical areas on turned wood objects. Too large to do by hand although happy to finish by hand. Thanks!

Did @artmusshort ever reply? I too need the axminster bs350 bandsaw manual. Thanks

Having repaired the frame of a lovely old victorian nursing chair, I'm now re-wickering the seat and back. One long and difficult job using the 7-step method, canes breaking and fraying if I do as advised on various YouTubes . Seems like soaking the canes for no more than 20min before using...

I'm also looking for a similar type of bandsaw, mostly for shaping bowl blanks. Needs to be able to take an 8-12" half log - throat. Suggestions please.

Thanks, I agree, used several makitas for years, all good solid gear. Will probably go for this.

any opinions on the MAKITA BO6050J DUAL ACTION sander. Looks like it might do more rough sanding to get rid of scuff and plane marks than the Bosch. The festool and Mirka look to be out of my price bracket (max £250-ish)

Thanks for the suggestions. There are a lot of festool sanders, suggestions as to which? From experience, it needs to be fairly aggressive at first.

My old sanders (belt and rectangular orbital) are not doing the job on a table top which I had planed off. The belt always leaves marks which the orbital can't get out. Any advice out there about good orbitals which might cut the mustard? About time I re-equipped.

yes, understood, and thanks again.

Thanks, that's a great idea as it allows me to use a heavy bar that hopefully won't wobble too much over distance. I appreciate the point about torsion. Will need to remain patient! By 'relieve' I guess you mean reduce the diameter a bit on the following sections of the bar, with the grinder, in...

Andy, thanks for the extra explanation! This is similar to what I've been doing with an augur fixed into a drill extension, but it wanders a lot on the way through and leaves a lot of eccentric mess which is difficult to clean up. I think I shall try the other suggestion of grinding a cutting...

I'm confused, Andy! Tim

I need to bore out 400-500mm x 10-20mm holes in one of my projects. My current augur bits aren't long enough and don't remain centred once you start drilling deep. Any suggestions either for long eg Forstner bits (can't find online so far) or for an extension bar that I could lock a drill into?

I'm planning an expanding table for our kitchen, seating 6 without central leaf and 8 with leaf in place. Most designs plank the top crossways but I want to use ash with a strong grain which I think will look better with the grain longways. Any reason NOT to do this? Apart from the obvious...

Thanks all for loads of valuable advice - got the motor inverted and everything is working well. Only problem is a developing knock which I'm pretty sure is motor bearings. This of course is a pain, as I have to dismantle the lathe to get the motor out again and, hopefully, fix it, although at...

One further question: I can't get clear info about whether the remote control (low voltage) cabling for on/of, forward/reverse and speed control potentiometer needs to be screened. Also, the instructions say the cable can be anything from 0.5mm to 1.5mm (20-14AWG) - that seems a huge range. Any...

I've now tested the motor, which I'm happy to find works, and have the inverter, and info re wiring plus switches for remote control. The instructions say clearly that the motor control wiring from the inverter needs to be screened, which I now have. Can you please tell me whether the remote...

Now I understand! That is so helpful - I'm really grateful for your advice and for the pics and info.

Thanks - very helpful and much more straightforward than other suggestions. I'm puzzled about the mounting - the motor and cradle are at the base of the headstock and it's not possible to mount anything below that. Also, mounting low down (inside the casing?) would require a remote speed/on/off...

Thanks - got the motor out now and it is dual voltage and looks like it can be wired in delta. Any suggestions about best inverter to go for? I've been in touch with ACDC Drives who recommend either a Parker AC10 or Yaskawa V1000 (do I need STO, whatever that is??). I definitely need a bit of...