Search results

It very much depends on the nature of the asbestos. if it was real artex then it doesn't fall under the 2012 regulations and it can be removed if suitable precautions are taken. honest answer is I'd get someone in to test it before I removed it. to remove it, depending on what it is I'd want...

Or the red knob above even.

Here. :D

right hand side at the back of the blade housing where it attaches to the sliding bar there i a small (8mm) silver knob. thats the lock pin. push down on the front handle to take the pressure of it then pull it out. it's not very obvious.

jobbers live in an index, spade and brad live in a blow modeled case and fostners live in a wooden box. scrap and broken bits are in an MDF box in a draw beneath the drill press along with oddities like pilot and hole bits that have been ground to do a job and plug cutters etc. new are stored...

Just noticed your tile size. Dont running bond them, they wint look right. Stack bond please.

Carbide hole saw. Sneaky tip is use a board with a hole in for the drill and clamp the tile so you can cut part holes on seperate tiles. Bit bigger than i was thinking. Running bond wont look to bad. Straight vertical lines in the adhesive please. :D

I dont know the tile size you are using. Drop a plumb and scibe a true vertical line about 3/4 of a tile from the corner. Check the corner is is plumb from that line. If its a brick wall it will be out. If its framed its more likely to plumb in at least 1 direction. Nornally you'd set from your...

Whatss the cost difference with chipboard floor? I found that osb sags between 16" joists.

The state of my work today id say plastering. :( it really is a skill you have to practice fairly regularly to keep your skill level up.

Last visit to a hairdresser/barbar was when I was 13 and they charged me 20 quid to shave it all off. Im now 39. Ive cut my own hair ever since, my wife did a barbers course, she does my sons and her fathers, occasionally she does mine, but its very rare. Thanks for the reminder, this...

Thats a machine rolled thread rather than a die cut thread (the major diameter is bigger than the shaft diameter), so it can't be that old but it doesn't mean it isn't some odd ball thread, hardware manufacturers love to chuck a curve ball in. how much meat is there in the backplate (of the...

Sorry was working in pipe rather than hose. Poly 14mm is 10mm id which would be fine. Rubber 14mm would be 6.3mm and to small. Id 14mm is a bugger to get Measure the run before you buy anything.

Chuck a hose through. No joins to worry about. Use 14mm if you can. Polyurethane will be fine. Hard pipe is great but for low pressure stuff its overkill.

I liked Sean rowes cover of vincent black lightning. https://youtu.be/CrGOs1a1lOk Didnt add the link for passanger on manchester "busking". https://youtu.be/JLb-Nr2Bdc8 Can i throw in justin johnson in the mix. https://youtu.be/cUiYamjM4GU Right ive broken this enough. Back you go thread.

This is why I know Passenger, this song, this performance. Yes I did sing along. :) Try Mary Spender https://www.youtube.com/watch?v=S6vbjt_b6dk or Nathan Rateliff https://www.youtube.com/watch?v=1iAYhQsQhSY something further left field? the dead south...

listened to passangers set yesterday whilst working. Larkin Poe haven't done a live set yet but release a song a week on youtube already so they've been gone . been some good theatre put on youtube recently too.

Today. Working on turning a largish amount of salvaged pine (10×2) into a very chunky bedframe, planed and jointed two edges, marked for biscuits, cut the biscuit slots test fit then glue and clamp. Hmmm thats funny, they lined up perfect with no gap before......... Oh wait, the big triangle i...

Cool,a human head to go on my hunting trophy wall. Heres the moose i shot (not really, mines wooden) https://www.instructables.com/id/Cardbo ... l-Hanging/

Using RGT, because it's free right now. At the end of all this I shall put the turbo trainer back where it belongs, and where it's lived for the past 6 years (under the table saw where I can't reach it) and go back to riding outside. I can manage maybe 40 minutes before I get to the point of...